APPLIED PLASTIC COATINGS, Inc.

Applied Plastic Coatings, Inc.

products and services

Engineered Coatings for Thermal Management

Cerakote Ceramic High Temp Cpatings www.nicindustries.com Polished four into one header.

“Chromex”

Most exhaust done within 5 to 10 working days



Engineered Coatings for Thermal Management

“Chromex”

Polished four into one header.

Pricing (subject to change)

  • Standard V-8 Header (full length) $295 set
  • Standard V-8 Header (short) $265 set
  • Standard V-8 Cast manifold* $250 set
  • Please inquire for other pricing

*due to casting irregularities, minor imperfections may exist in the polish.

The most popular coating of its kind on the market today. Its combination of ceramic and aluminum are applied, then baked on, and machined polished to a very Attractive, hard, durable finish with many benefits:

  • Thermal barrier properties for reduced under hood temperatures.
  • Increased gas velocities for horsepower gains averaging 2%
  • Lifetime guarantee against corrosion
  • Rapid cool down
  • Will not blue up to 1300 DEG. F

Our coating service includes all necessary preparation for coating adhesion.


“Other Available Colors”

steel gray header

Steel Grey shown above. White shown to left. Black, Gold, and Satin Silver also available.

Pricing (subject to change)

  • Standard V-8 Header (full length) $220 set
  • Standard V-8 Header (short) $200 set
  • Standard V-8 Cast manifold $225 set
  • Please inquire for other pricing

This family of heat cured ceramic reinforced coating (available in several colors) are some of the most effective thermal barrier coatings available, increasing performance, while extending component life. The insulating fillers used in this coating keeps heat inside the header and out of the engine compartment where lower temperatures permit more dense fuel / air charges to reach combustion chambers. Unlike header wraps, these coatings do not hold potentially damaging heat around the part. Rather, the surface temperatures are actually reduced, extending the life of the part.

  • Rated for temperatures from 1200 to 1800 DEG. F. depending on color.
  • Thermal barrier properties for reduced under hood temperatures.
  • Increased gas velocities for horsepower gains averaging 2%.

Our coating service includes all necessary preparation for coating adhesion.

white side pipes

White will have more iregularites than other colors.


Ultra High Temp “Turbine Coat”

header

Pricing (subject to change)

  • Standard V-8 Header (full length) $220 set
  • Standard V-8 Header (short) $200 set
  • Standard V-8 Cast manifold $225 set
  • Please inquire for other pricing

This heat cured ceramic reinforced coating is the most effective thermal barrier coating available, increasing performance, while extending component life. Tested to over 2000 deg. F, the insulating fillers used in this coating keeps heat inside the header and out of the engine compartment where lower temperatures permit more dense fuel / air charges to reach combustion chambers. Unlike header wraps, this coating does not hold potentially damaging heat around the part. Rather, the surface temperatures are actually reduced, extending the life of the part.

  • Tested to over 2000 DEG. F.
  • Thermal barrier properties for reduced under hood temperatures
  • Increased gas velocities for horsepower gains averaging 2%
  • Especially effective on turbo housings

Our coating service includes all necessary preparation for coating adhesion.


“Internal Exhaust Coating”

end view showing internal coating

For protecting chrome pipes or for those wishing to impart the maximum thermal barrier properties, and obtain a smother interior surface for enhanced exhaust flow.

A ceramic based coating used as an internal lining to achieve maximum insulating properties between exhaust gases and the metal surface. The greatest benefit is realized at the area where the exhaust hits the first bend in the pipe, however a complete lining will result in maximum benefit. Great for exhaust ports. Pipes must be new to be guaranteed.

  • Minimize or in most cases eliminate chrome pipe bluing
  • Obtain maximum thermal barrier properties
  • Improve exhaust gas velocity, increase hp.

Our coating service includes all necessary preparation for coating adhesion.

Pricing upon request

Internal ceramic filled barrier coating


“Insulkote”

Insulkote

This optional undercoat was designed to increase the temperature rating of any of our exhaust coatings. Insulkote series high temperature ceramic thermal barrier underlayment was designed to provide superior thermal barrier protection for use on exhaust systems. Along with this, Insulkote also provides increased heat transfer reduction, and works as shielding when applied as a base coat under high temperature coatings.

Formulated to reduce heat transfer, Insulkote offers long-term protection against metal fatigue, corrosion, and deterioration. Insulkote increases performance and horsepower by increasing heat scavenging during exhaust cycle.

Our coating service includes all necessary preparation for coating adhesion.


Other products and services

Miscellaneous pieces.
  • Thermal dispersant coating, increases the ability of the part to radiate heat (i.e. .motorcycle cylinder / heads.)
  • Powder coating, complete surface prep. 1000 + colors and special effects, including thermoplastics
  • Thin film dry film lubrication (i.e. pistons, mechanical linkage, pivot points etc.)

Polished four into one header.
Polished four into one header.

CERAMIC EXHAUST COATINGS

Due to variations in monitors and printers, colors may vary. Ask for hard sample if color is critical.
Visit our West Metro Denver showroom:
5000 Tabor St.
Wheat Ridge, Colorado 80033

* ENGINEERING * SALES * SERVICE *
a unique family of coating products and services
STAIR CAP™ Stair products